Linear Gate Motor & Opener Nationwide

Linear Gate Motor & Opener in West Palm Beach: What to Know First

Most Linear gate motor repairs in West Palm Beach run between $185 and $640, depending on whether we’re replacing a limit switch or a full swing-arm operator. We carry Linear-compatible parts on the truck for the most common models, and most repairs are completed in one visit, usually within two to three hours of arrival. The price is written and handed to you before we touch a tool, never after.

Call (561) 725-8048

This page is for homeowners in West Palm Beach with a Linear opener already installed who want to know what’s wrong, what it costs, and whether it’s worth fixing. If that’s you, call (561) 725-8048. Adrian Vance, our owner, still reviews every Linear diagnostic report personally.

How Linear Products Fail - and How We Fix Them

• Linear LDO series swing-arm operators: the limit switch drifts. On the LDO50 and LDO33 models, we repeatedly see the open-limit cam back off its set screw after a few hundred cycles. The gate overshoots the open stop by a few degrees, then the board throws a fault. The fix is resetting the limit and applying a drop of thread locker so it stays. We photograph the new setting before we leave.
• Linear APeX series slide motors: the chain tensioner bracket cracks. The APeX slide operators use a stamped steel bracket to hold the chain idler. In West Palm Beach’s salt air, that bracket rusts faster than Linear’s documentation suggests, especially within three miles of the Intracoastal. When it snaps, the chain jumps and the gate stalls mid-travel. We replace the bracket with a stainless aftermarket equivalent and re-tension to spec.
• Linear VS-GSLG and VS-GSLG-B: capacitor failure mimics a dead board. Homeowners get quoted a full control-board replacement when the real fault is a $20 start capacitor. The symptom: the motor hums but won’t move under load, or it trips the breaker after two seconds. We test the capacitor first, because a bad cap presents exactly like a burned relay on the board. You don’t pay for a board you didn’t need.
• Linear MegaCode receivers: phantom remote failures. We’ve diagnosed more “dead” Linear remotes in West Palm Beach that turned out to be a MegaCode receiver whose antenna wire had corroded inside its insulation. No signal, no movement, but the receiver tests fine on the bench. We replace the antenna run, not the receiver, and the remotes come back to life. We check this before selling you a new radio.
• Linear MDR and DDR keypads: moisture intrusion at the keypad face. Florida humidity gets inside the keypad membrane on older Linear MDR units, which causes ghost entries - the gate opens on its own at 3 a.m. because the membrane has shorted across the entry circuit. We seal the replacement keypad with a proper gasket and dielectric grease on the connector. The factory install rarely does.

Our Linear Gate Motor & Opener Process

1. 1
   Call and describe what the gate is doing. A live person answers at (561) 725-8048. We ask for the model number off the operator label if you can get to it safely. That tells us which parts to load.
2. 2
   Diagnostic visit with written findings. We test the board voltage, the capacitor, the limit switches, and the photo-eye alignment. You get a written list of what we found, our hourly rate, and the flat price for the fix, all before you approve anything.
3. 3
   Parts decision: OEM vs. aftermarket. For Linear operators, we use OEM where the warranty is still active or where the part is safety-critical, like control boards and stop circuits. For wear items like brackets and capacitors, we use quality aftermarket parts that outlast the factory originals in West Palm Beach’s salt air
4. 4
   The repair itself. Most Linear motor repairs take one to three hours on site. Slide-motor chain replacements run longer if the drive rail needs realigning.
5. 5
   Load test and photo documentation. We cycle the gate ten times under load, check the reversing sensitivity, and photograph the final state: the new limit-switch position, the part number installed, the wiring terminations. You get that photo record before we leave.
6. 6
   365-Day Done Right Promise. If anything about our Linear repair fails within one year, we return and make it right at no charge. The promise is in writing on your invoice.

Before

After

What Linear Gate Motor & Opener Costs in West Palm Beach

Here are the numbers we quote most often for Linear work in West Palm Beach:

• Service call and diagnostic: $85. Applied toward the repair if you approve it on the spot.
• Capacitor replacement (fixed the “hum but won’t move” symptom): $185-$265. Includes the part, labor, and a full load test.
• Limit-switch reset and calibration: $150-$220. What we charge for the LDO drift problem described above.
• Chain tensioner bracket replacement on an APeX slide motor: $340-$490. Includes the stainless bracket, chain re-tension, and rail alignment.
• Full Linear swing-arm operator replacement: $640-$980. Depends on whether the arm bracket is intact and whether we’re reusing the existing photo-eyes.

What moves the price: whether the gate is swing or slide, how far the operator is from a power source, and whether we’re working on rusted hardware that needs cutting. The price you approve is the price you pay. We never add a line item after the fact.

Call (561) 725-8048 for a free estimate on your exact Linear setup.

Why West Palm Beach Homeowners Call Vance Gate Repair West Palm Beach for Linear Work

We’re an independent Linear service provider, not a factory-authorized dealer, which means our recommendation is based on what’s best for your gate, not on what protects a manufacturer relationship. We service nine gate-automation brands, including LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so a Linear job doesn’t force you into a Linear replacement if another brand’s part fits better.

What you get on every Linear repair: a written flat price before work begins, a named and background-checked technician dispatched to your property, and a documented photo record of what was found and what was replaced. That’s Haven Standard Clause 1 and Clause 4 in practice. If the repair isn’t right, the 365-Day Done Right Promise means we make it right, no argument and no fee, within a full year.

We’ve repaired and installed over 22,000 gates since 2014, and every single one had a written price before the job started. Adrian Vance started in commercial access-control work, and he still insists on the documentation habits that field taught him. I’ll tell you what I found, what it takes to fix it, and what you’ll have when I leave. That’s not a tagline. That’s the work order.

FAQs