Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGhost Controls Gate Repair in Westgate, FL | Vance Gate Repair West Palm Beach
We specialize in Gate Repair - Westgate for Ghost Controls gate openers, and we’ve been doing it since 2014. The thing that makes Ghost Controls work different here is this: Westgate is unincorporated Palm Beach County, and a lot of these openers were installed without permits decades ago. When a post shifts or a board corrodes out, the repair often triggers a code-compliance step that incorporated cities don’t require. If your Ghost Controls gate is acting up, call (561) 725-8048 and we’ll tell you what’s actually wrong before anyone touches a tool.
Why Westgate Residents Choose Us for Ghost Controls Service
We’ve worked on Ghost Controls openers in Westgate long enough to know which failures show up on which blocks. The AXS1 and AXS2 swing arms on 1960s ranch homes behave differently than the TSS1 slide units on the few larger lots near the western edge of the neighborhood. We carry OEM Ghost Controls boards, arms, and accessories, and we source aftermarket equivalents only when OEM parts are discontinued or the cost no longer makes sense for the gate’s remaining life. Adrian Vance founded this company after years of commercial access-control work, and the habit stuck: every Westgate job gets a written price before we start, and a photo record of what we found and changed before we leave. We’re an independent Ghost Controls service provider, not a manufacturer affiliate or authorized dealer. That independence means we recommend repair when repair makes sense, and we tell you straight when it doesn’t.
Common Ghost Controls Gate Repair Problems We Solve in Westgate
- Control board corrosion from humidity and salt air. Westgate sits 10 to 12 miles inland, but the humidity here is relentless. We regularly open Ghost Controls control boxes on Haverhill Road and find green-tinted corrosion across the board terminals. The gate either stops responding to remotes or the arm moves erratically. We clean, test, and replace the board when it’s gone too far.
- Limit switch misalignment after post shift. Westgate’s loose sandy fill lets gate posts move over time. When a post tilts even a few degrees, the Ghost Controls limit switch readings go with it. The gate overruns the open position or stops a foot short of closed. We re-set the post, then recalibrate and photograph the new switch positions.
- Stripped nylon gears in the arm drive. Older iron gates in Westgate are heavy, and many went years without lubrication under absentee landlords. The nylon gear inside the Ghost Controls arm strips out, leaving the motor spinning with no gate movement. We replace the gear or the arm assembly, and we show you the old part.
- Phantom activations from damaged loop detectors. The afternoon thunderstorm season hits Westgate hard. Lightning nearby takes out loop detector boards, which makes the gate open and close on its own or refuse to close at all. We diagnose the loop first before blaming the opener.
- Dead batteries and failed battery backups. After any extended power flicker or storm outage, Ghost Controls openers without a working backup battery lose their limits and sometimes their programming. We install and test the DPB battery backup kit so the gate holds its settings through the next storm.
Three sub-services matter most for these failures: motor repair, remote control work, and weld and rust repair on the gate itself. We handle all three on the same visit when the job calls for it.
BeforeAfterGhost Controls Service in Westgate: What Local Conditions Mean for Your Equipment
Westgate is an older unincorporated Palm Beach County community, and a large share of the driveway gates here were installed before 2000, many without permits. That single fact changes how Ghost Controls repairs play out. Palm Beach County enforces current Florida Building Code wind-load and anchoring requirements on repair and replacement work in unincorporated areas like Westgate. So when a hurricane shifts a palm tree or fence post and the Ghost Controls opener on a gate that was never permitted gets flagged, a straightforward board replacement turns into a bigger job: post re-setting, wind-rating verification, and a permit pull. Incorporated cities like West Palm Beach don’t enforce those same private-gate requirements. We’ve had to re-set posts and pull permits before we could even touch the opener on more than one Westgate property, which is why some homeowners choose our Gate Installation in Westgate to start fresh with a fully permitted system. If you own a Gatehouse Road or Bald Cypress Drive home with an older Ghost Controls unit, assume the county may need to sign off before the repair is complete. We handle that paperwork as part of the job, and it’s in the written scope before we start.
Ghost Controls Models & Products We Service in Westgate
We service the Ghost Controls AXS1 single swing gate opener, the AXS2 dual swing gate opener, the TSS1 slide gate opener, and the DPB battery backup kit. Most Westgate homes have the AXS1 or AXS2 on single or double driveway gates. The TSS1 shows up less often, usually on wider or commercial-adjacent lots. We keep common OEM boards, arms, remotes, and limit switches on the truck for same-day repairs in Westgate. When a Ghost Controls part is discontinued, we tell you before we substitute an aftermarket equivalent, and we note the part number on your invoice so no future technician has to guess. For more detail on our broader Ghost Controls work, see our Ghost Controls sales & service page.
Ghost Controls Service Pricing in Westgate
Most Ghost Controls repairs in Westgate run between $180 and $340 for common fixes like limit switch replacement, remote reprogramming, or board cleaning. Full control board replacement usually lands between $280 and $450 depending on the model and whether the wiring harness needs replacing too. A complete opener swap on a single swing gate typically runs $600 to $950 installed. What drives the cost here: whether the post has shifted, whether the county requires a wind-load upgrade or permit, and whether the existing gate is heavy enough to have damaged the arm gears. Every quote is written and handed over before work starts. You’ll know the price before we touch the opener. For an exact figure on your Ghost Controls gate, call (561) 725-8048 and we’ll give you a free estimate in writing.
Serving Westgate, FL - Our Local Coverage Area
We’re based in the Westgate area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Ghost Controls Gate Repair in Westgate
It depends on what the repair involves and whether the county flags the existing installation. Palm Beach County enforces Florida Building Code wind-load and anchoring rules on unincorporated-area gate work, so if we’re re-setting posts or replacing the opener, a permit is often required. If the opener was never permitted originally, the county may require the whole installation be brought up to current code before the repair can be finalized. We handle the permit pull and the code compliance as part of the written scope, and we’ll tell you upfront if your property will need it. Call (561) 725-8048 and we’ll check your specific situation before anything gets touched.
The grinding is usually the nylon gear inside the arm drive stripping against the motor, and the timing with the storm is often coincidental or heat-related. Westgate’s humidity accelerates corrosion on the arm’s internal components, and if the gate post has shifted in sandy soil, the arm binds and grinds under load. We open the arm, inspect the gear and the post alignment, and replace the stripped parts or re-set the post as needed. Call (561) 725-8048 for a free estimate before the gear fails completely.
Yes. The DPB battery backup kit works with existing Ghost Controls openers, and we install it regularly on Westgate gates that already have an AXS1 or AXS2 running. It keeps the gate operating through power flickers and short outages, and it preserves limit settings so the gate doesn’t need reprogramming after every storm. The install is typically done in under an hour, and we include it in the written price before we start.
The most common cause is corrosion on the control board antenna connection or interference from nearby electrical equipment. In Westgate’s dense housing, we also see cases where a neighbor’s gate remote on the same frequency causes signal washout or the receiver board has been damaged by a lightning strike. We test the remote, inspect the receiver board, and replace the antenna or board as needed. Call (561) 725-8048 and we’ll figure out which one it is.
If the hinge plates are rusted but the gate frame and post are sound, replacing the plates is usually the right call. On heavier Westgate iron gates with deep rust at the hinges and corroded latch hardware, we sometimes find the post itself is compromised inside the sandy footing, and new hinge plates won’t hold. We’ll show you the condition of the post and the gate steel before recommending replacement. Call (561) 725-8048 and we’ll give you a written answer with photos.
Service Areas Near Westgate
Beyond Westgate itself, we run Ghost Controls service calls into West Palm Beach, Riviera Beach, Lake Park, North Palm Beach, and Royal Palm Beach. If you’re in a neighboring community, see our Westgate service area details or our Ghost Controls service in Riviera Beach and Ghost Controls service in West Palm Beach pages.
Book Your Ghost Controls Service in Westgate Today
If your Ghost Controls gate is misbehaving in Westgate, call (561) 725-8048. We’ll schedule a visit, put the price in writing before any work starts, and leave you with a photo record of exactly what we found and fixed. Same-day service is available for most Ghost Controls repairs in Westgate.
Written by Adrian Vance, Owner at Vance Gate Repair West Palm Beach, serving Westgate since 2014.