Ghost Controls Keypad & Intercom Repair Nationwide

Ghost Controls Keypad & Intercom Repair: The West Palm Beach Owner’s Guide

Ghost Controls keypad and intercom repair in West Palm Beach typically runs $190 to $385 installed, depending on whether we’re swapping a failed keypad, replacing a corroded intercom board, or rewiring the entire entry station. We stock Ghost Controls-compatible keypads and intercom components on our trucks, so most West Palm Beach calls are completed the same visit. Most owners discover the problem the same way: the keypad lights up but won’t trigger the gate, the intercom crackles and drops the call, or the buttons start requiring three or four presses before anything happens.

Call (561) 725-8048

What you’re seeing is usually one of three things: water intrusion in the housing, a failed membrane switch, or a control board that’s lost communication with the operator. Adrian Vance will tell you what he found, what it takes to fix it, and what you’ll have when he leaves. That’s how we run every Ghost Controls call in West Palm Beach.

Key takeaways:

• Most Ghost Controls keypad and intercom repairs run $190-$385 installed
• We stock Ghost Controls-compatible parts on the truck for same-visit repair
• Written price before any work starts, per our Haven Standard
• 365-Day Done Right Promise covers every Ghost Controls part we install

Which Ghost Controls Models This Applies To

Ghost Controls sells two keypad lines that account for nearly all West Palm Beach residential installs: the AXDP (the weatherproof die-cast keypad) and the AXDP2 (the newer revision with backlit keys). The intercom side is usually the AC series wire-free intercom, which pairs a gate station with an in-home handset. If you have a Ghost Controls opener, your keypad or intercom will be one of these three units about 95% of the time.

The compatibility gotcha with Ghost Controls is the receiver frequency. Older Ghost Controls openers shipped with a 318 MHz receiver. Newer units run 433 MHz. A keypad that worked perfectly with your 2018-era operator will not pair with a 2023 receiver, even if the physical connector looks identical. We verify the receiver frequency before we quote anything, because installing a 318 MHz keypad on a 433 MHz system is a $250 mistake that won’t show up until you’re standing at the gate pressing a dead button. The sticker on the opener control board tells us which one you have.

You can buy Ghost Controls OEM parts through their dealer network. You can also find aftermarket keypads labeled “compatible with Ghost Controls.” Here’s the honest version: the aftermarket keypads work fine for basic entry, but the seal quality and keypad membrane tend to fail faster in South Florida humidity. For West Palm Beach, where we get salt air along Flagler Drive and daily afternoon thunderstorms, we recommend OEM for the keypad and acceptable aftermarket for the intercom handset, where the electronics live indoors.

Vance Gate Repair West Palm Beach is an independent service provider. We’re not affiliated with Ghost Controls, but we stock their parts, we know their wiring, and we service them alongside LiftMaster, Mighty Mule, DoorKing, and every other major brand we carry parts for.

Signs Your Ghost Controls Keypad & Intercom Repair Is Failing

• Keypad lights up but the gate doesn’t move. This is almost always a frequency mismatch or a lost pairing. The keypad’s got power, the button membrane works, but the signal isn’t reaching the receiver. Sometimes the pairing was wiped by a power surge; sometimes the receiver board on the opener has died. We test both ends before replacing anything.
• Buttons need repeated presses to register. The membrane switch under the keypad face is wearing out. Once one key starts failing, the rest follow within a few months. This is the single most common Ghost Controls failure we see in West Palm Beach, and it’s usually water intrusion from a hairline crack in the housing seal.
• Intercom crackles, buzzes, or drops the audio. The board inside the gate station is corroding. Even the weatherproof housings accumulate condensation in Florida’s humidity cycle, and once corrosion starts on the board traces, it doesn’t stop. You can clean it, and you’ll buy yourself a few weeks, but the failure will return.
• The intercom rings but nobody can hear you outside. This is typically the microphone element or the speaker cone in the gate station. Both are replaceable without swapping the whole intercom, and it’s a $60 to $90 repair versus $250-plus for a full gate station replacement.
• Keypad works but only from two feet away. Your keypad’s internal antenna has degraded or the housing is shielding the signal. We see this on units that have been hit by lightning nearby or that have had the internal wiring pinched during a previous battery change. Sometimes it’s repairable; sometimes the board has to go.

Before

After

Replacement Cost & What’s Included

Here’s the range we quote in West Palm Beach:

What drives the range: whether the existing wiring is intact and reusable, whether the keypad is 318 MHz or 433 MHz, and whether the gate station housing needs replacement or can be cleaned and resealed. The written price we hand you before any work starts includes the part, the labor, the wiring check, and the programming to your operator. It does not change after we open the housing, because we’ve done this enough times to know what we’re getting into.

Every Ghost Controls keypad or intercom we install carries our 365-Day Done Right Promise. If the part fails inside a year, we replace it. No argument, no fee, no expiration dance. And per Haven Standard Clause 4, you leave with a photographed record of what was found, what was installed, and how it was programmed.

DIY or Call Us?

The keypad and intercom side of a Ghost Controls system is low-voltage, which means you’re not dealing with the kind of risk you’d find inside the operator itself. The high-tension springs and 12-volt motor wiring that can genuinely hurt someone live in the gate operator, not the entry keypad. So if you want to try the basics, here’s what’s safe: check that the keypad has fresh batteries, confirm the breaker for the gate operator is on, and verify the intercom handset inside the house is still plugged into power. Those three checks fix about 15% of our West Palm Beach calls without a service visit.

Where DIY goes wrong: pairing a Ghost Controls keypad requires entering the operator’s learn mode, which is on the control board inside the operator housing. That housing contains the high-tension spring and the capacitor. If you’re not comfortable working around a charged capacitor, don’t open the operator. Second, guessing wrong on frequency wastes $200 or more on a part that won’t pair. We test the frequency, the receiver, and the keypad output before we quote a part number. That’s what the written price pays for: certainty, not guesswork.

If the fix is outside your comfort zone, call (561) 725-8048 and we’ll put a technician on it. Same-visit repair is normal for keypad and intercom work in West Palm Beach, and the price is on paper before any tool comes out.

FAQs

Talk to a Technician Who Knows Ghost Controls

If your Ghost Controls keypad or intercom is acting up in West Palm Beach, call (561) 725-8048. A live person answers, day or night. We’ll get a technician to your gate, diagnose the problem in plain terms, and hand you a written price before anything gets touched. That’s how we’ve handled every one of the 22,000-plus gates we’ve repaired since 2014, and it’s how we’ll handle yours.

Written by Adrian Vance, Owner, Vance Gate Repair West Palm Beach at Vance Gate Repair West Palm Beach, serving West Palm Beach and nearby areas.