Ghost Controls Gate Parts & Welding Nationwide

Ghost Controls Gate Parts & Welding in West Palm Beach: What to Know First

Ghost Controls gate parts repair and welding in West Palm Beach runs $145 to $480 for most hinge replacements, rail repairs, and bracket welds, with full post replacements typically landing between $600 and $1,200. We carry OEM Ghost Controls replacement parts plus quality aftermarket options for the discontinued and current model lines, and most parts jobs are completed the same day the part is in hand. As an independent Ghost Controls service provider, we price every job in writing before any work starts.

Call (561) 725-8048

This page is for West Palm Beach homeowners who own a Ghost Controls system, have identified a mechanical issue, and want the straight answer on what it takes to fix it. Whether you’re in Flamingo Park, Southland Park, or out near the Bear Lakes, call (561) 725-8048 and we’ll diagnose what’s actually wrong. No charge for the estimate.

How Ghost Controls Products Fail - and How We Fix Them

• AXS series hinge pins seize and egg-out the post bracket holes. The AX series (AXS-1 single, AXS-2 dual) shipped with steel hinge pins that run inside un-bushed aluminum brackets. In West Palm Beach’s humidity and salt air, galvanic corrosion binds the pin and the bracket. The pin stops turning, the hinge face friction climbs, and the motor works harder until the limit logic trips early. We drill to the next clean size, fit a bronze bushing, and weld any elongated holes shut before re-boring. The gate swings freely again instead of groaning halfway through travel.
• Older Ghost Controls swing arms snap at the clevis mounting plate. The first-generation Ghost Controls swing gate openers (the models before the AX series) used a single-arm actuator with a bolted clevis at the gate bracket. That clevis takes every push and every wind gust. After six or seven West Palm Beach summers, the plate fatigues at the bolt line and the arm drops. We weld a gusseted replacement plate in place, not a bolt-on patch. The repair outlasts the original part because it’s thicker and supported where the load actually is.
• Slide gate v-wheels and guide rollers bind on unleveled track sections. Ghost Controls hybrid slide openers rely on a flat, level run of track. We routinely see track joints that have shifted a half-inch or more as West Palm Beach’s sandy soil settles under the slab. The v-wheel rides the rail edge, flats a spot, and the gate jerks through travel. Our fix is realigning the track, shimming the low sections, and replacing the v-wheels and guide rollers. If the rail itself is twisted, we weld in a splice and re-grind the joint smooth.
• Ghost Controls photo-eye posts get knocked out of alignment and the gate refuses to close. The photo-eye mounts are on flimsy stalks that a mower tap or a mailbox bump moves just enough to break the beam. The gate then reads an obstruction and reverses. It’s not a board failure; it’s geometry. We replace the stamped stalk with a welded steel post set in concrete, align the eyes, and photograph the positions so you have a record.
• Latch and lock bars on Ghost Controls-equipped gates rust at the weld seams. Nearly every Ghost Controls dual gate in West Palm Beach uses a center latch or a magnetic lock bar to hold the second leaf. The factory weld where the latch pin meets the bar is the first thing to rust through near the coast. We cut out the failed section, weld in a fresh stainless pin and receiver, and re-coat the bar. Latch repairs typically run $85 to $180, including the parts and the weld.

Our Ghost Controls Gate Parts & Welding Process

1. 1
   Call and describe the symptom. You reach a live person at (561) 725-8048. We ask what the gate is doing, not what you think the part number is. That comes later.
2. 2
   On-site diagnosis. We come out, put eyes on the Ghost Controls opener, hinges, track, and weld points. We test travel, check limit settings, and measure play in every joint. You get a written description of what we found.
3. 3
   Parts decision. If the part is a Ghost Controls OEM component still in production, we quote it. If it’s long discontinued, we show you a quality aftermarket equivalent and explain the difference. Either way, the price is written down before we touch a tool.
4. 4
   The repair. Hinges get re-bored and bushed. Brackets get welded and ground. Track gets leveled. Latch bars get cut and rebuilt. We photograph the work as it progresses.
5. 5
   Testing and documentation. We cycle the gate through a dozen full opens and closes, verify the Ghost Controls limit settings are where they need to be, and confirm the safety edges and photo-eyes interrupt properly. You get the photo log and the written part list before we leave.
6. 6
   The 365-Day Done Right Promise. If anything we touched isn’t right within a year, we come back and make it right. No argument, no fee.

Before

After

What Ghost Controls Gate Parts & Welding Costs in West Palm Beach

What moves the price: whether the post is concrete-set or bolt-down, how much welding the bracket damage requires, and whether we’re sourcing a current Ghost Controls OEM part or an aftermarket equivalent for a dropped line. Every quote is pushed into your hands on paper before work starts, under Clause 1 of our Haven Standard. Call (561) 725-8048 for an exact written estimate. Estimates are free.

Why West Palm Beach Homeowners Call Vance Gate Repair West Palm Beach for Ghost Controls Work

Most West Palm Beach gate companies will take a Ghost Controls job, but few can tell you the difference between the AXS actuator arm and the first-generation swing arm clevis without pulling the manual. We can, because we’ve repaired enough of both. Adrian Vance has been doing this since 2014, starting with commercial access-control sites where documentation was mandatory. That habit never left. Every Ghost Controls job we run leaves a photographed record of what was found, what was replaced, and how it was set. No future technician has to guess. No homeowner pays twice to rediscover the same problem.

A live person answers the phone 24/7, not a callback queue. If your Ghost Controls opener runs on a board we’ve seen fail before, we’ll tell you that. And if your system is beyond repair, we’re not steering you toward one brand: we service LiftMaster, Mighty Mule, DoorKing, and six other automation lines, so the replacement conversation is about what fits your gate, not what’s on our truck. Free second opinion on any written estimate from another company, too. Bring the paperwork and we’ll review it. No charge.

FAQs